[Q47-Q62] Real Exam Questions NACE-CIP2-001 Dumps Exam Questions in here [Apr-2022]

Rate this post

Real Exam Questions NACE-CIP2-001 Dumps Exam Questions in here [Apr-2022]

Get Latest Apr-2022 Conduct effective penetration tests using NACE-CIP2-001

NEW QUESTION 47
You are the NACE Level 2 Inspector with the final responsibility to prepare the final report for a very large structural steel shop project which has gone very well. It is due next week. The work has been ongoing for two years and several NACE Level 1 Inspectors have worked under your supervision throughout the project. You find you are missing one week of daily reports for the night shift from the very beginning of the project and despite your best efforts they are cannot found.
You FIRST preferred course of action is to:

Use creative writing to cover over the fact they are missing

Plainly state in your report that they are missing

Do not complete your report until they can be found

Re-create the reports as not much was going on during night shift anyway

NEW QUESTION 48
Non-Conformance Reports are designed to:

Punish the Contractor for substandard work

Elevate the status of the Inspector

Assist the Owner in negotiating credits from the Contractor

To identify items that do not meet the specification requirements

NEW QUESTION 49
When performing testing in accordance with ASTM D 2583 the inspector may observe:

Adhesion failure

Cohesion failure

Glue failure

Cold flow or creep

NEW QUESTION 50
The HATE adhesion tester uses

compressed air to apply pressure to the test dolly.

mechanical means only to apply pressure to the test dolly.

a special tape to apply pressure to the test dolly.

a hydraulic piston to apply pressure to the test dolly.

NEW QUESTION 51
A reinforced coating is

equally resistant to movement and impact as a non-reinforced coating.

equally resistant to abrasion and impact as a non-reinforced coating.

less resistant to movement, abrasion, and impact than a non-reinforced coating.

more resistant to movement, abrasion, and impact than a non-reinforced coating.

NEW QUESTION 52
You are NACE Level 2 Inspector working on a tank lining job where a mobile centrifugal blast unit is being used to blast the tank floor to a NACE No.1/SSPC SP 5. The Contractor has completed his final blast and has called for a hold point inspection. This is the 1 st time you have seen field based centrifugal blast cleaning. You observe what appears to be staining on the substrate however the Contractor assures you this is normal when using centrifugal blast units and what you are seeing is what is defined in the standard as an acceptable variation in appearance.
Your FIRST preferred course of action is to:

Request that the Contractor re-blast the floor

Review the standard with the Contractor and re-inspect the floor

Shut the job down

Call your supervisor

NEW QUESTION 53
Differences in technique for abrasive blasting concrete versus steel require the operator to:

Lower the blast pressure

Move the nozzle quicker

Increase the standoff distance

a), b) and c)

NEW QUESTION 54
Cold-applied tape

are identifiable by its distinct colors, usually light blue, green, Or Grey.

is typically green or led and looks like “painted” finish.

have a cross-linked polyethylene backing and a heat-activated adhesive.

is polyethylene film, heat laminated, ‘With an adhesive layer of butyl glue.

NEW QUESTION 55
NACE Standards include:

Standard Practices

Material Requirements

a) & b)

a) only

NEW QUESTION 56
When performing an adhesion test in accordance with ASTM D 3359 where the Dry Film Thickness is approximately 10 mils, the Inspector should use:

Method A – X Cut

Method A – Cross Hatch

Method B – X cut

Method B – Cross Hatch

NEW QUESTION 57
When environmental enclosures are being used an inspector needs to be concerned about:

Lighting

Air changes

Structural integrity

a), b), and c)

NEW QUESTION 58
In the event of a conflict between the Product Data Sheet and the Specification:

The Product Data Sheet prevails

The Specification prevails