Ace NACE NACE-CIP2-001 Certification with Actual Questions Jan 11, 2023 Updated [Q17-Q36] : Testking Free Dumps : http://blog.testkingfree.com

NEW QUESTION 17
You are the NACE Level 2 Inspector on a project where overcoating of galvanized steel is being performed. The specification references SSPC SP 16 as the surface preparation method. At the pre-job meeting operations personnel make it clear that abrasive blasting will not permitted. The Owner’s representative asks you what other methods might be used.
Of the options shown below, what would be the preferred option in this situation?

SP 1 followed by acid etching

SP 1 followed by caustic etching

SP 1 followed by SP 2

SP 1 followed by SP 3

NEW QUESTION 18
NACE International Standards are developed by:

Government mandates

International mandates

Standard committees

Regional mandates

NEW QUESTION 19
WJ-1 is always performed using UHWJ at pressures above 210 MPa (30,000 PSI)

True

False

NEW QUESTION 20
Which type of pipelines collect the gas from the transmission system so utility companies can distribute the gas to end users?

Gathering

Midstream

Transmission

Distribution

NEW QUESTION 21
Coating application to concrete substrates is:

More challenging than coating steel

Less challenging, than coating steel

The same as coating steel

Not required as Concrete is inorganic

NEW QUESTION 22
External coatings applied to buried pipelines are generally tested for:

Gloss level

Chalking resistance

Cathodic disbondment

Solvent resistance

NEW QUESTION 23
You are NACE Level 2 Inspector working on a tank lining job where a mobile centrifugal blast unit is being used to blast the tank floor to a NACE No.1/SSPC SP 5. The Contractor has completed his final blast and has called for a hold point inspection. This is the 1 st time you have seen field based centrifugal blast cleaning. You observe what appears to be staining on the substrate however the Contractor assures you this is normal when using centrifugal blast units and what you are seeing is what is defined in the standard as an acceptable variation in appearance.
Your FIRST preferred course of action is to:

Request that the Contractor re-blast the floor

Review the standard with the Contractor and re-inspect the floor

Shut the job down

Call your supervisor

NEW QUESTION 24
Steel shot grit contaminated with oil or grease used in a cetrifugal blast cleaning should be

washed with clean potable water prior to Use.

mixed with uncontaminated abrasive

run through the air wash separator.

disposed of properly.

NEW QUESTION 25
The coating applicator has ignored a enface preparation hold point and applied coating over the surface without a sign off from you as the inspector.
Your FIRST preferred course of action is to:

Stop the job

Require the Applicator to remove the coating

Advise the Owner and write a Non-Conformance report

Ignore the situation

NEW QUESTION 26
NACE/SSPC Water Jetting standards are directly equivalent to ISO Abrasive Blast Standards:

True

False

NEW QUESTION 27
Generally for safety considerations, waterjetting hose connections use

an oil/water separator.

a long wand.

a whip-lock device.

filters.

NEW QUESTION 28
Thermal Spray coatings provide:

Barrier protection

Inhibitive protection

Sacrificial protection

Thermal protection

NEW QUESTION 29
You are the NACY Coating Inspector on a tank lining project where desiccant dehumidification is being used. Since the first shift of abrasive blasting your readings have indicated relative humidity below 40%; however on the second shift of coating application your readings are indicting 80%.
Your FIRST preferred course of action is to:

Check to See if the dehumidification equipment is operating correctly

Call your supervisor

Advise the coating applicator supervisor of your readings

Document the readings at the end of the shift

NEW QUESTION 30
You are the NACE Level 2 Coating Inspector where SSPC PA 2 has been specified with an additional requirement that no individual gauge reading shall be below a certain value.
As this is not part of the standard you should:

Ignore the additional requirement

Enforce the additional requirement

Call your supervisor

Request clarification from the specifier

NEW QUESTION 31
When working with someone who is very concerned about Stability and maintaining adherence to the status-quo, the Inspector should try to:

Implement immediate to get them motivated

Give them as much advance notice as possible about upcoming changes

Challenge their value to the team and try to get them out of their comfort zone

Make sure they are the center of attention in all site meetings

NEW QUESTION 32
The main reason dehumidification is used during coating operations is to

control the environment

reduce the possibility of missing the recoat window.

allow the contractor to guarantee the completion date.

avoid repetitive blasting/coating operations.

NEW QUESTION 33
NACE Level 2 Inspectors have been authorized to perform:

All types of inspection without supervision

Visual inspection and Non-destructive testing

Visual inspection, Non-Destructive and Destructive testing

Visual inspection only

NEW QUESTION 34
Inspectors perform tests on linings that they may not perform on exterior coatings because

coatings are more durable than linings.

coatings are expected to degrade over time.

linings protect the contents and the container.

linings are more durable than coatings.

NEW QUESTION 35
When environmental enclosures are being used an inspector needs to be concerned about:

Lighting

Air changes

Structural integrity

a), b), and c)

NEW QUESTION 36
When observing design defects the NACE Inspector should:

Document the defect and the potential problems that could result

Ignore the defect as the inspector can’t change the design

Request that the item be rebuilt with a better design for coating

Stop the job immediately