300-410 Study Guide Latest [Jul 19, 2023] Realistic Verified 300-410 Dumps [Q170-Q184] : Testking Free Dumps : http://blog.testkingfree.com

NO.170 Drag and drop the MPLS VPN concepts from the left onto the correct descriptions on the right.

NO.171

Refer to the exhibit. After redistribution is enabled between the routing protocols; PC2, PC3, and PC4 cannot reach PC1.
Which action can the engineer take to solve the issue so that all the PCs are reachable?

Set the administrative distance 100 under the RIP process on R2.

Filter the prefix 10.1.1.0/24 when redistributed from OSPF to EIGRP.

Filter the prefix 10.1.1.0/24 when redistributed from RIP to EIGRP.

Redistribute the directly connected interfaces on R2.

NO.172

Refer to the exhibit. The Los Angeles and New York routers are receiving routes from Chicago but not from each other Which configuration fixes the issue?

Interface Tunnel1
no ip split-horizon eigrp 111

Interface Tunnel1
Ip next-hop-self elgrp 111

Interface Tunnel1
tunnel mode Ipsec Ipv4

Interface Tunnel1
tunnel protection ipsec profile IPSec-PROFILE

NO.173 Exhibit.

A network is configured for EIGR equal-cost balancing, but the traffic destined to the servers is not load balance. …..resolve the issue?

208 oon R3 E0/0

120 on R4 E0/1

120/on R3 E0/1

2200 on R4 E0/1

NO.174 Refer to Exhibit:

AS 111 wanted to use AS 200 as the preferred path for 172.20.5.0/24 and AS 100 as the backup. After the configuration, AS 100 is not used for any other routes. Which configuration resolves the issue?

route-mmap SETLP permit 10
match ip address prefix-list PLIST1
set local-preference 99
route-map SETLP permit 20

route-map SETLP permit 10
match ip address prefix-list PLIST1
set local-preference 110
route-map SETLP permit 20

router bgp 111
no neighbor 192.168.10.1 route-map SETLP in
neighbor 192.168.10.1 route-map SETLP out

router bap 111
no neighbor 192.168.10.1 route-map SETLP in
neighbor 192.168.20.2 route-map SE TLP in

NO.175 Refer to the exhibit.

An engineer is trying to generate a summary route in OSPF for network 10.0.0.0/8, but the summary route does not show up in the routing table. Why is the summary route missing?

The summary-address command is used only for summarizing prefixes between areas.

The summary route is visible only in the OSPF database, not in the routing table.

There is no route for a subnet inside 10.0.0.0/8, so the summary route is not generated.

The summary route is not visible on this router, but it is visible on other OSPF routers in the same area.

NO.176 Refer to the exhibit.

After redistribution is enabled between the routing protocols, PC2, PC3, and PC4 cannot reach PC1. Which action can be engineer take to solve the issue so that all the PCs are reachable?

Filter the prefix 10.1.1.0/24 when redistributed from OSPF to EIGRP.

Set the administrative distance 100 under the process on R2.

Filter the prefix 10.1.1.0/24 when redistributed from RIP to EIGRP.

Redistribute the directly connected interfaces on R2.

NO.177 Refer to the exhibit.

AAA server 10.1.1.1 is configured with the default authentication and accounting settings, but the switch cannot communicate with the server Which action resolves this issue?

Match the authentication port

Match the accounting port

Correct the timeout value.

Correct the shared secret.

NO.178 Refer to the exhibits. The output of the trace route from R5 shows a loop in the network.
Which configuration prevents this loop?

NO.179 Refer to the exhibit.

An engineer is troubleshooting BGP on a device but discovers that the clock on the device does not correspond to the time stamp of the log entries Which action ensures consistency between the two times?

Configure the logging clock synchronize command in global configuration mode

Configure the service timestamps log uptime command in global configuration mode

Configure the service timestamps log datetime localtime command in global configuration mode

Make sure that the clock on the device is synchronized with an NTP server

NO.180 Refer to the exhibit.

An engineer must filter incoming EIGRP updates to allow only a set of specific prefixes. The distribute list is tested, and it filters out all routes except network 10.10.10.0/24. How should the engineer temporarily allow all prefixes to be learned by the routers again without adjusting the existing access list?

A permit 20 statement should be added before completing the ACL with the required prefixes, and then the permit 20 statement can be removed.

A permit any statement should be added before completing the ACL with the required prefixes and then the permit any statement can be removed.

A continue statement should be added within the permit 10 statement before completing the ACL with the required prefixes, and then the continue statement can be removed.

An extended access list must be used instead of a standard access list to accomplish the task

NO.181 Refer to the exhibit.

An administrator noticed that after a change was made on R1, the timestamps on the system logs did not match the clock.
What is the reasons for this error?

The keyword localtime is defined on the timestamp service command.

The NTP server is in an different time zone.

An authentication error with the NTP server results in an incorrect timestamp.

The system clock is set incorrectly to summer-time hours

NO.182 Refer to the exhibit.

AS111 is receiving its own routes from AS200 causing a loop in the network. Which configuration provides loop prevention?
A)

B)

C)

D)

Option A

Option B

Option C

Option D

NO.183 Which command allows traffic to load-balance in an MPLS Layer 3 VPN configuration?

multi-paths eibgp 2

maximum-paths 2

maximum-paths ibgp 2

multi-paths 2

NO.184 Drag and drop the DHCP messages from the left onto the correct uses on the right.