Free 201 Exam Study Guide for the NEW [Dec-2023] Dumps Test Engine [Q78-Q92]

Rate this post

Free 201 Exam Study Guide for the NEW [Dec-2023] Dumps Test Engine

201 PDF Dumps Extremely Quick Way Of Preparation

To prepare for the F5 201 (BIG-IP Administrator) Certification Exam, candidates need to have a strong understanding of networking concepts and technologies, as well as experience working with F5 products and solutions. 201 exam consists of 80 multiple-choice questions and takes 90 minutes to complete. Candidates need to achieve a passing score of 69% to earn the certification. Once certified, individuals can demonstrate their expertise in managing and administering F5 solutions, which can lead to new job opportunities and career advancement.

Q78. Which three iRule events are likely to be seen in iRules designed to select a pool for load balancing. (Choose 3)

CLIENT_DATA

SERVER_DATA

HTTP_REQUEST

HTTP_RESPONSE

CLIENT_ACCEPTED

SERVER_SELECTED

SERVER_CONNECTED

Q79. A BIG-IP Administrator needs to check the memory utilization on a BIG-IP system. Which two methods can the UIG IP Administrator use? (Choose two.)

Run the tmsh show/sys memory command

Run the tmsh show/sys traffic command

Go to Statistics > Module Statistics > Traffic Summary in the configuration utility

Go to Statistics > Module Statistics > Memory in the configuration utility

Go to System > Disk Management in the configuration utility

Q80. A BIG-IP Administrator is setting up a new BIG-IP device. The network administrator reports that the interface has an incompatible media speed. The BIG-IP Administrator needs to change this setting manually.
From which location should the BIG-IP Administrator perform this task?

On the Front Console

In the TMOS Shell Command line

In the Configuration Utility, Network > Interface

In the Configuration Utility, System > Configuration

Q81. A BIG-IP Administrator uses a device group to share the workload and needs to perform service on a BIG-IP device currently active for a traffic group. The administrator needs to enable the traffic group to run on another BIG-IP device in the device group. What should the administrator do to meet the requirement?

Create a new Traffic Group and then fail to Standby Unit

Select Traffic Group and then select Failover

Select Traffic Group and then select Force to Standby

Select Traffic Group on Primary Unit and then select Demote

Q82. Refer to the exhibit.

Which TMSH command generated this output?

tmsh list /cm sync-status

tmsh show /sys sync-status

tmsh list /sys sync-status

tmsh show /cm sync status

Q83. A BIG-IP Administrator needs to have a BIG-IP linked to two upstream switches for resilience of the external network. The network engineer who is going to configure the switch instructs the BIG-IP Administrator to configure interface binding with LACP. Which configuration should the administrator use?

A virtual server with an LACP profile and the switches’ management IPs as pool members.

A virtual server with an LACP profile and the interfaces connected to the switches as pool members.

A Trunk listing the allowed VLAN IDs and MAC addresses configured on the switches.

A Trunk containing an interface connected to each switch.

Q84. Which process or system can be monitored by the BIG-IP system and used as a failover trigger in a redundant pair configuration?

bandwidth utilization

duplicate IP address

CPU utilization percentage

VLAN communication ability

Q85. A BIG-IP Administrator adds new Pool Members into an existing, highly utilized pool. Soon after, there are reports that the application is failing to load for some users. What pool level setting should the BIG-IP Administrator check?

Availability Requirement

Allow SNAT

Action On Service Down

Slow Ramp Time

Explanation
Option ABC is a global configuration, has nothing to do with the new pool member, select D after excluding

Q86. During a high-demand traffic event, the BIG-IP Administrator needs to limit the number of new connections per second allowed to a Virtual Server.
What should the administrator apply to accomplish this task?

An HTTP Compression profile to the Virtual Server

A connection rate limit to the Virtual Server

A connection limit to the Virtual Server

A OneConnect profile to the Virtual Server

Q87. Which statement accurately describes the difference between two loadElbalancing modes specified as “member” and “node”.

There is no difference; the two terms are referenced for backward compatibility purposes.

When the loadElbalancing choice references “node”, priority group activation is unavailable.

LoadElbalancing options referencing “nodes” are available only when the pool members are defined for the “any” port.

When the loadElb alancing choice references “node”, the addresses’ parameters are used to make the loadElbalancing choice rather than the member’s parameters.

Q88. A BIG-IP Administrator needs to determine which pool members in a pool have been manually forced offline and are NOT accepting any new traffic. Which status icon indicates this?
A)

B)

C)

D)

Option

Q89. A site wishes to perform source address translation on packets from some clients but not others. The determination is not based on the client’s IP address, but on the virtual servers their packets arrive on. What could best accomplish this goal?

A SNAT for all addresses could be defined, and then disable the SNAT processing for select VLANs.

Some virtual servers could be associated with SNAT pools and others not associated with SNAT pools.

The decision to perform source address translation is always based on VLAN. Thus, the goal cannot be achieved.

The decision to perform source address translation is always based on a client’s address (or network). Thus, this goal cannot be achieved.

Q90. A BIG-IP Administrator finds the following log entry:
tnm tmm[7141]: 011e0002:4: sweeperjjpdate: aggressive mode activated.
Which action should the BIG-IP Administrator to mitigate this memory issue?

Configure the redundant par to be active-active

Decrease the TCP profile ide Timeout value

increase the TCP profile ide Timeout value

Configure the serve to use Connection Mirroring

Q91. A BIG-IP device sends out the following SNMP trap:
big-ipo.f5.com – bigipExternalLinkChange Link: 1.0 is DOWN
Where in the BIG-IP Configuration utility should the BIG-IP Administrator verify the current status of Link
1.0?

System > Platform

Network > Trunks > Trunk List

Statistics > Performance > System

Network > Interfaces > Interface List

Explanation
1.0 is a physical interface, you can see the interface status from the physical interface in the network.

Q92. An LTM device has a virtual server mapped to www.f5.com with a pool assigned. Users report that when browsing, they are periodically required to re-login to /resources/201.1.7.b.2_l.com. The objects are defined as follows:
Virtual server. Destination 192.168.245.100:443 netmask 255.255.255.0
Persistence: SSL session persistence
Profiles: HTTP/TCP
Which persistence method should the BIG-IP Administrator apply to resolve this issue?

Source address affinity

hexadecimal

SIP

Destination address affinity

Loading …