[Jul 10, 2024] Latest Fortinet NSE7_OTS-7.2 Exam Practice Test To Gain Brilliante Result [Q11-Q26] : Testking Free Dumps : http://blog.testkingfree.com

NEW QUESTION 11
Which three Fortinet products can be used for device identification in an OT industrial control system (ICS)?
(Choose three.)

FortiNAC

FortiManager

FortiAnalyzer

FortiSIEM

FortiGate

NEW QUESTION 12
Which type of attack posed by skilled and malicious users of security level 4 (SL 4) of IEC 62443 is designed to defend against intentional attacks?

Users with access to moderate resources

Users with low access to resources

Users with unintentional operator error

Users with substantial resources

NEW QUESTION 13
What are two benefits of a Nozomi integration with FortiNAC? (Choose two.)

Enhanced point of connection details

Direct VLAN assignment

Adapter consolidation for multi-adapter hosts

Importation and classification of hosts

NEW QUESTION 14
In a wireless network integration, how does FortiNAC obtain connecting MAC address information?

RADIUS

Link traps

End station traffic monitoring

MAC notification traps

NEW QUESTION 15
An OT architect has deployed a Layer 2 switch in the OT network at Level 1 the Purdue model-process control. The purpose of the Layer 2 switch is to segment traffic between PLC1 and PLC2 with two VLANs.
All the traffic between PLC1 and PLC2 must first flow through the Layer 2 switch and then through the FortiGate device in the Level 2 supervisory control network.
What statement about the traffic between PLC1 and PLC2 is true?

The Layer 2 switch rewrites VLAN tags before sending traffic to the FortiGate device.

The Layer 2 switches routes any traffic to the FortiGate device through an Ethernet link.

PLC1 and PLC2 traffic must flow through the Layer-2 switch trunk link to the FortiGate device.

In order to communicate, PLC1 must be in the same VLAN as PLC2.

NEW QUESTION 16
Refer to the exhibit.

You need to configure VPN user access for supervisors at the breach and HQ sites using the same soft FortiToken. Each site has a FortiGate VPN gateway.
What must you do to achieve this objective?

You must use a FortiAuthenticator.

You must register the same FortiToken on more than one FortiGate.

You must use the user self-registration server.

You must use a third-party RADIUS OTP server.

NEW QUESTION 17
An OT supervisor has configured LDAP and FSSO for the authentication. The goal is that all the users be authenticated against passive authentication first and, if passive authentication is not successful, then users should be challenged with active authentication.
What should the OT supervisor do to achieve this on FortiGate?

Configure a firewall policy with LDAP users and place it on the top of list of firewall policies.

Enable two-factor authentication with FSSO.

Configure a firewall policy with FSSO users and place it on the top of list of firewall policies.

Under config user settings configure set auth-on-demand implicit.

NEW QUESTION 18
When device profiling rules are enabled, which devices connected on the network are evaluated by the device profiling rules?

Known trusted devices, each time they change location

All connected devices, each time they connect

Rogue devices, only when they connect for the first time

Rogue devices, each time they connect

NEW QUESTION 19
Refer to the exhibit.

An operational technology rule is created and successfully activated to monitor the Modbus protocol on FortiSIEM. However, the rule does not trigger incidents despite Modbus traffic and application logs being received correctly by FortiSIEM.
Which statement correctly describes the issue on the rule configuration?

The first condition on the SubPattern filter must use the OR logical operator.

The attributes in the Group By section must match the ones in Fitters section.

The Aggregate attribute COUNT expression is incompatible with the filters.

The SubPattern is missing the filter to match the Modbus protocol.

NEW QUESTION 20
The OT network analyst run different level of reports to quickly explore failures that could put the network at risk. Such reports can be about device performance. Which FortiSIEM reporting method helps to identify device failures?

Business service reports

Device inventory reports

CMDB operational reports

Active dependent rules reports

NEW QUESTION 21
Refer to the exhibit.

An OT network security audit concluded that the application sensor requires changes to ensure the correct security action is committed against the overrides filters.
Which change must the OT network administrator make?

Set all application categories to apply default actions.

Change the security action of the industrial category to monitor.

Set the priority of the C.BO.NA.1 signature override to 1.

Remove IEC.60870.5.104 Information.Transfer from the first filter override.

Explanation
According to the Fortinet NSE 7 – OT Security 6.4 exam guide1, the application sensor settings allow you to configure the security action for each application category andnetwork protocol override. The security action determines how the FortiGate unit handles traffic that matches the application category or network protocol override. The security action can be one of the following:
Allow: The FortiGate unit allows the traffic without any further inspection.
Monitor: The FortiGate unit allows the traffic and logs it for monitoring purposes.
Block: The FortiGate unit blocks the traffic and logs it as an attack.
The priority of the network protocol override determines the order in which the FortiGate unit applies the security action to the traffic. The lower the priority number, the higher the priority. For example, a priority of 1 is higher than a priority of 10.
In the exhibit, the application sensor has the following settings:
The industrial category has a security action of allow, which means that the FortiGate unit will not inspect or log any traffic that belongs to this category.
The IEC.60870.5.104 Information.Transfer network protocol override has a security action of block, which means that the FortiGate unit will block and log any traffic that matches this protocol.
The IEC.60870.5.104 Control.Functions network protocol override has a security action of monitor, which means that the FortiGate unit will allow and log any traffic that matches this protocol.
The IEC.60870.5.104 Start/Stop network protocol override has a security action of allow, which means that the FortiGate unit will not inspect or log any traffic that matches this protocol.
The IEC.60870.5.104 Transfer.C.BO.NA.1 network protocol override has a security action of block, which means that the FortiGate unit will block and log any traffic that matches this protocol.
The problem with these settings is that the IEC.60870.5.104 Transfer.C.BO.NA.1 network protocol override has a lower priority than the IEC.60870.5.104 Information.Transfer network protocol override. This means that if the traffic matches both protocols, the FortiGate unit will apply the security action of the higher priority override, which is block. However, the IEC.60870.5.104 Transfer.C.BO.NA.1 protocol is used to transfer binary outputs, which are essential for controlling OT devices. Therefore, blocking this protocol could have negative consequences for the OT network.
To fix this issue, the OT network administrator must set the priority of the IEC.60870.5.104 Transfer.C.BO.NA.1 network protocol override to 1, which is higher than the priority of the IEC.60870.5.104 Information.Transfer network protocol override. This way, the FortiGate unit will apply the security action of the lower priority override, which is allow, to the traffic that matches both protocols. This will ensure that the FortiGate unit does not block the traffic that is used to transfer binary outputs, while still blocking the traffic that is used to transfer information.
1: NSE 7 Network Security Architect – Fortinet

NEW QUESTION 22
Which three Fortinet products can be used for device identification in an OT industrial control system (ICS)?
(Choose three.)

FortiNAC

FortiManager

FortiAnalyzer

FortiSIEM

FortiGate

NEW QUESTION 23
Refer to the exhibit and analyze the output.

Which statement about the output is true?

This is a sample of a FortiAnalyzer system interface event log.

This is a sample of an SNMP temperature control event log.

This is a sample of a PAM event type.

This is a sample of FortiGate interface statistics.

NEW QUESTION 24
Refer to the exhibits.

Which statement about some of the generated report elements from FortiAnalyzer is true?

The report confirms Modbus and IEC 104 are the key applications crossing the network.

FortiGate collects the logs and generates the report to FortiAnalyzer.

The file types confirm the infected applications on the PLCs.

This report is predefined and is not available for customization.

NEW QUESTION 25
Refer to the exhibit.

You are navigating through FortiSIEM in an OT network.
How do you view information presented in the exhibit and what does the FortiGate device security status tell you?

In the PCI logging dashboard and there are one or more high-severity security incidents for the FortiGate device.

In the summary dashboard and there are one or more high-severity security incidents for the FortiGate device.

In the widget dashboard and there are one or more high-severity incidents for the FortiGate device.

In the business service dashboard and there are one or more high-severity security incidents for the FortiGate device.

NEW QUESTION 26
Refer to the exhibit, which shows a non-protected OT environment.

An administrator needs to implement proper protection on the OT network.
Which three steps should an administrator take to protect the OT network? (Choose three.)

Deploy an edge FortiGate between the internet and an OT network as a one-arm sniffer.

Deploy a FortiGate device within each ICS network.

Configure firewall policies with web filter to protect the different ICS networks.

Configure firewall policies with industrial protocol sensors

Use segmentation