Free FCSS_NST_SE-7.4 Braindumps Download Updated on Jan 25, 2025 with 42 Questions [Q18-Q40] : Testking Free Dumps : http://blog.testkingfree.com

NEW QUESTION 18
Refer to the exhibit, which shows the output ofa debug command.

Which two statements about the output are true? (Choose two.)

The interlace is part of the OSPF backbone area.

There are a total of five OSPF routers attached to the vorz4 network segment

One of the neighbors has a router ID of 0.0.0.4.

In the network connected to port4, two OSPF routers are down.

NEW QUESTION 19
Refer to the exhibit, which shows the output o! the BGP database.

Which two statements are correct? (Choose two.)

The advertised prefix of 10.20.30.0’24 was configured using the network command.

The first four prefixes are being advertised using a legacy route advertisement.

The advertised prefix of 10.20.30.0’24 is being advertised through the redistribution of another routing protocol.

The output shows all prefixes advertised by all neighbors as well as the local router.

NEW QUESTION 20
Exhibit.

Refer to the exhibit, which contains a screenshot of some phase 1 settings.
The VPN is not up. To diagnose the issue, the administrator enters the following CLI commands on an SSH session on FortiGate:

However, the IKE real-time debug does not show any output. Why?

The administrator must also run the command diagnose debug enable.

The debug shows only error messages. If there is no output, then the phase 1 and phase 2 configurations match.

The log-filter setting is incorrect. The VPN traffic does not match this filter.

Replace diagnose debug application ike -1 with diagnose debug application ipsec -1.

NEW QUESTION 21
Which statement about IKEv2 is true?

Both IKEv1and IKEv2 share the feature of asymmetric authentication.

IKEv1and IKEv2 have enough of the header format in common that both versions can run over the same UDP port.

IKEv1and IKEv2 use same TCP port but run on different UDP ports.

IKEv1and IKEv2 share the concept of phase1and phase2.

NEW QUESTION 22
Refer to the exhibit.

Assuming a default configuration, which three statements are true? (Choose three.)

Strict RPF is enabled by default.

User B: Fail. There is no route to 95.56.234.24 using wan2 in the routing table.

User A: Pass. The default static route through wan1 passes the RPF check regardless of the source IP address.

User B: Pass. FortiGate will use asymmetric routing using wan1 to reply to traffic for 95.56.234.24.

User C: Fail. There is no route to 10.0.4.63 using port1 in the touting table.

NEW QUESTION 23
Which authentication option can you not configure under config user radius on FortiOS?

mschap

pap

mschap2

eap

NEW QUESTION 24
Refer to the exhibit, which shows partial outputs from two routing debug commands.

Which change must an administrator make on FortiGate to route web traffic from internal users to the internet, using ECMP?

Set snat-route-change to enable.

Set the priority of the static default route using port2 to 1.

Set preserve-session-route to enable.

Set the priority of the static default route using port1 to 10.

NEW QUESTION 25
Refer to the exhibit, which shows a partial output of the fssod daemon real-time debug command.

What two conclusions can you draw Itom the output? (Choose two.)

The workstation with IP 10.124.2.90 will be polled frequently using TCP port 445 to see if the user is still logged on.

The logon event can be seen on the collector agent installed on Windows.

FSSO is using DC agent mode to detect logon events.

FSSO is using agentless polling mode to detect logon events.

NEW QUESTION 26
Which two statements about an auxiliary session ate true? (Choose two.)

With the auxiliary session selling disabled, only auxiliary sessions are offloaded.

With the auxiliary session setting enabled. ECMP traffic is accelerated to the NP6 processor.

With the auxiliary session setting enabled. Iwo sessions are created in case of routing change.

With the auxiliary session setting disabled, for each traffic path. FortiGate uses the same auxiliary session.

NEW QUESTION 27
Which statement about parallel path processing is correct (PPP)?

PPP chooses froma group of parallel options lo identity the optimal path tor processing a packet.

Only FortiGate hardware configurations affect the path that a packet takes.

PPP does not apply to packets that are part of an already established session.

Software configuration has no impact on PPP.

NEW QUESTION 28
Exhibit.

Refer to the exhibit, which shows a partial web fillet profile configuration.
Which action does FortiGate lake if a user attempts to access www. dropbox. com, which is categorized as File Sharing and Storage?

FortiGate allows the connection, based on the URL Filter configuration.

FortiGate blocks the connection as an invalid URL.

FortiGate exempts the connection, based on the Web Content Filter configuration.

FortiGate blocks the connection, based on the FortiGuard category based filter configuration.

NEW QUESTION 29
What are two reasons you might see iprope_in_check() check failed, drop when using the debug flow?
(Choose two.)

Packet was dropped because of policy route misconfiguration.

Packet was dropped because of traffic shaping.

Trusted host list misconfiguration.

VIP or IP pool misconfiguration.

NEW QUESTION 30
Exhibit.

Refer to the exhibit, which shows the output of a session. Which two statements are true? (Choose Iwo.)

The TCP session has been successfully established.

The session was initiated from an authenticated user.

The session is being inspected using flow inspection.

The session is being offloaded.

NEW QUESTION 31
Which two statements are true regarding heartbeat messages sent from an FSSO collector agent to FortiGate?
(Choose two.)

The heartbeat messages can be seen using the command diagnose debug authd fsso list.

The heartbeat messages can be seen in the collector agent logs.

The heartbeat messages can be seen on FortiGate using the real-lime FSSO debug.

The heartbeat messages must be manually enabled on FortiGate.

NEW QUESTION 32
An administrator wants to capture encrypted phase 2 traffic between two FotiGate devices using the built-in sniffer.
If the administrator knows that there Is no NAT device located between both FortiGate devices, which command should the administrator run?

diagnose sniffer packet any ‘udp port 500’

diagnose sniffer packet any ‘lp proto 50’

diagnose sniffer packet any ‘udp port 4500’

diagnose sniffer packet any ‘ah’

NEW QUESTION 33
Refer to theexhibit,which shows the output of getrouter info ospf neighbor.

What can you conclude from the command output?

The network type connecting the local Fortigate and OSPF neighbor 0.0.0.10 is point-to-point.

All neighbors are in area 0.0.0.0.

The local FortiGate is the BDR.

The local FortiGate is not a DROther.