View All 4A0-265 Actual Exam Questions, Answers and Explanations for Free [Q24-Q40]

Rate this post

View All 4A0-265 Actual Exam Questions, Answers and Explanations for Free

4A0-265 Exam Free Practice Test with100% Accurate Answers

NEW QUESTION 24
Consider the exhibit.

Which type of loopback is applied?

Client port facility loopback

Client port terminal Ioopback

Line port facility Ioopback

Line port terminal Ioopback

NEW QUESTION 25
Which of the following Performance Measurement (PM) type is NOT typically retrieved at an Optical Transponder (OT) line interface?

Digital Wrapper (DW)

Ethernet collision counters

Forward Error Correction – Errors Counted (FEC-EC)

Optical Power Received (OPR)

NEW QUESTION 26
A “Power Adjustment Required” alarm was raised on the ingress amplifier in slot 1/10. Which of the following commands should be entered to manually adjust the related amplifier optical power levels?

config powermgmt ingress 1/10 scot

config powermgmt ingress 1/10 power adjustment

config powermgmt ingress 1/10

config powermgmt ingress 1/10 adjust

NEW QUESTION 27
What is the default severity level for a Threshold Crossing Alert (TCA) alarm?

Critical

Major

Minor

Warning

NEW QUESTION 28
Consider the exhibit. What do the different colored green columns indicate?

Optical power levels measured multiple times against a specific interface, at 24-hour intervals for the same wavelength.

Optical power levels measured for multiple wavelengths against a specific interface.

Optical power levels measured at different interfaces throughout the optical path of a single wavelength.

The average optical power levels measured for multiple wavelengths throughout their shared optical path.

NEW QUESTION 29
Which of the following statements best describes the payload type setting?

Payload type attribute is recorded within the client payload and must be entered manually.

Payload type attribute Is recorded within the client payload and can be set automatically.

Payload type attribute is recorded within the OTN overhead and must be entered manually.

Payload type attribute is recorded within the OTN overhead and can be set automatically or manually.

NEW QUESTION 30
Which of the following statements about the alarm masking mechanism is TRUE?

The alarm masking mechanism makes sure that alarms are always present on the downstream interfaces to facilitate the troubleshooting process.

The alarm masking mechanism updates the events’ original time stamps when it masks/shows alarms, so that when an alarm is not masked anymore, the user can see the updated date and time associated with the original issue.

The alarm masking mechanism always forwards masked alarms to an external Network Management System (NMS) for alarm correlation.

The alarm masking mechanism preserves the events’ original time stamps, when related alarms gets hidden and then eventually displayed because of the mechanism itself, so that the user can still know the date and time of the original issue.

NEW QUESTION 31
Which of the following is NOT a characteristic of an Optical Supervisory Channel Loss of Signal (OSC LOS) issue, in case that no “LD Input LOS” alarms are raised against the involved amplifiers?

An “Incoming SUPVY LOS” alarm is raised on the local node.

A “Data Link Down” alarm is raised on the adjacent node.

A “Power Adjustment Required” alarm is eventually raised on the local node.

Traffic does not pass between the local and adjacent nodes.

NEW QUESTION 32
Which of the following statements correctly describes where power adjustments can be performed?

In bidirectional configurations, ingress power adjustments are performed against the ingress amplifiers, while egress power adjustments are performed against the egress amplifiers.

In bidirectional configurations, both ingress and egress power adjustments are performed against the ingress amplifiers only.

In unidirectional configurations, both ingress and egress power adjustments are performed against the ingress amplifiers only.

When Raman pumps are used, both ingress and egress power adjustments are performed against the Raman pump directly.

NEW QUESTION 33
Consider the exhibit. A single directional fiber cut is occurring between two amplifiers in unidirectional configuration with Raman pump.
Multiple services are crossing the affected span.
Which node(s) will report an Incoming Payload LOS” alarm?

No node, as a Raman pump is used in Node A.

Node C only.

Both Node A and Node C

Neither Node A nor Node C.

NEW QUESTION 34
Suppose a channel-related alarm is reported on an 1830 PSS node, and is related to a possible Wave Keys clock source issue. What is the recommended order for the following troubleshooting steps?

1. Retrieve the channel power trace.
2. Determine the active clock reference source.
3. Switch to alternate clock source (PF).
4. Replace the suspect PF.

1. Retrieve the channel power trace.
2. Replace the suspect PF.
3. Determine the active clock reference source.
4. Switch to alternate clock source (PF).

1. Determine the active clock reference source.
2. Replace the suspect PF.
3. Retrieve the channel power trace.
4. Switch to alternate clock source (PF).

1. Replace the suspect PF.
2. Retrieve the channel power trace.
3. Switch to alternate clock source (PF).
4. Determine the active clock reference source.

NEW QUESTION 35
Consider the exhibit which shows an EPT Power ManagementReport for an ingress amplifier.
What is the available output optical power range?

-0.6 to 1.72 dB

-0.02 to 1.14 dB

0.56 to 1.14 dB

0.56 to 1.72 dB

NEW QUESTION 36
Suppose a node is experiencing a little unexpected attenuation over the Optical Supervisory Channel (OSC) transmit direction. Which of the following statements is FALSE?

No OSC-related alarms will raise on the local node.

A “Data Link Down” alarm will raise on the adjacent node.

A Power adjustments action will fail on the local node.

Traffic will pass between the local and adjacent node.

NEW QUESTION 37
Which of the following statements best describes the output of the CLI command: show wavekey wtmonitor
1/6/LINE summary?

A list of all channels detected against the selected interface (in and out); it shows if a Wave Keys pair is expected, if a Wave Keys pair is received, and if the received Wave Keys pair is unexpected.

A list of all channels on this interface for which any Wave Keys pair is being received.

A list of all channels detected against the selected interface, including Wave Keys pair, channel status, expected and measured power, allowed deviation, and tolerance.

A list of the unexpected channels detected against the selected interface.

NEW QUESTION 38
Which of the following statements about using Nokia product documentation in the troubleshooting process is TRUE?

Before investigating a problem it is important to check the Engineering and Planning Tool User Guide (EPTUG) if a possible issue has already been acknowledged by the Product Unit (PU).

The Customer Release Notes (CRNs) provides instructions to perform the automated provisioning, commissioning, and power balancing functions in a customer network based on the Nokia 1830 PS5 platform.

Before investigating a problem it is important to check the User Provisioning Guide (UPG) if a possible issue has already been acknowledged by the Product Unit (PU).

The Customer Release Notes (CRNs) document collects documented solved known issues, new issues discovered after the product software has been released.as well as software upgrade procedures and firmware details.

NEW QUESTION 39
Which of the following commands is used to retrieve the total output power level?

show interface am2125a 1/6/lineout

show interface am2125a 1/6/lineout detail

show interface am212 5a 1/6/lineout pm

show interface am2125a 1/6/lineout wavekey