300-410 Exam PDF [2024] Tests Free Updated Today with Correct 575 Questions [Q158-Q178]

4.5/5 - (2 votes)

300-410 Exam PDF [2024] Tests Free Updated Today with Correct 575 Questions

Cisco 300-410 Exam Preparation Guide and PDF Download

Q158. Refer to the exhibit.

The R1 and R2 configurations are:

The neighbor is not coming up. Which two sets of configurations bring the neighbors up? (Choose two.) A)

B)

C)

D)

E)

Option A

Option B

Option C

Option D

Option E

Q159. Exhibit:

Which action resolves the authentication problem?

Configure the user name on the TACACS+ server

Configure the UDP port 1812 to be allowed on the TACACS+ server

Configure the TCP port 49 to be reachable by the router

Configure the same password between the TACACS+ server and router.

Q160. Drag and drop the SNMP attributes in Cisco IOS devices from the left onto the correct SNMPv2c or SNMPV3 categories on the right.

Q161. Which list defines the contents of an MPLS label?

20-bit label; 3-bit traffic class; 1-bit bottom stack; 8-bit TTL

32-bit label; 3-bit traffic class; 1-bit bottom stack; 8-bit TTL

20-bit label; 3-bit flow label; 1-bit bottom stack; 8-bit hop limit

32-bit label; 3-bit flow label; 1-bit bottom stack; 8-bit hop limit

Q162. Refer to the exhibit.

Which configuration configures a policy on R1 to forward any traffic that is sourced from the 192.168.130.0/24 network to R2?

Option A

Option B

Option C

Option D

Q163. Refer to the exhibit.

Which interface configuration must be configured on the spoke A router to enable a dynamic DMVPN tunnel with the spoke B router?

Option A

Option B

Option C

Option D

Q164. Drag and drop the MPLS concepts from the left onto the descriptions on the right.

Q165. Refer to the exhibit.

A company with autonomous system number AS65401 has obtained IP address block 209.165.200.224/27 fro, ARIN. The company needed more IP addresses and was assigned block 209.165.202.128/27 from ISP2. An engineer is ISP1 reports they are receiving ISP2 routes from AS65401. Which configuration onR1 resolves the issue?
A)

B)

C)

D)

Option A

Option B

Option C

Option D

Q166. Refer to the exhibit.

The output of the trace route from R5 shows a loop in the network. Which configuration prevents this loop?
A)

B)

C)

D)

Option A

Option B

Option C

Option D

Q167. Refer to the exhibit.

An IP SLA was configured on router R1 that allows the default route to be modified in the event that Fa0/0 loses reachability with the router R3 Fa0/0 interface. The route has changed to flow through router R2. Which debug command is used to troubleshoot this issue?

debug ip flow

debug ip sla error

debug ip routing

debug ip packet

Q168. R2 has a locally originated prefix 192.168.130.0/24 and has these configurations:

What is the result when the route-map OUT command is applied toward an eBGP neighbor R1 (1.1.1.1) by using the neighbor 1.1.1.1 route-map OUT out command?

R1 sees 192.168.130.0/24 as two AS hops away instead of one AS hop away.

R1 does not accept any routes other than 192.168.130.0/24

R1 does not forward traffic that is destined for 192.168.30.0/24

Network 192.168.130.0/24 is not allowed in the R1 table

Q169. An engineer configured a Cisco router to send reliable and encrypted notifications for any events to the management server. It was noticed that the notification messages are reliable but not encrypted. Which action resolves the issue?

Configure all devices for SNMPv3 informs with priv.

Configure all devices for SNMPv3 informs with auth.

Configure all devices for SNMPv3 traps with auth.

Configure all devices for SNMPv3 traps with priv.

Q170. Which transport layer protocol is used to form LDP sessions?

UDP

SCTP

TCP

RDP

Q171.

Refer to the exhibit R2 can reach Loopback222, but R1 SW1 and PC1 cannot communicate with 172.16.222
254 R1 and R2 configurations are shown here

Which EIGRP configuration command resolves the issue?

R2(config-router) # redistribute static

R1(conftg-router)# network 172.16.222.254 0.0.0.0

R1 (config-router)# network 172.16.222.264 255.255.255.255

R1(config-router)# redistribute static

Q172. Drag and drop the IPv6 first hop security device roles from the left onto the corresponding descriptions on the right.

Q173. Refer to the exhibit.

Which command must be configured to make VRF CCNP work?

interface Loopback0
vrf forwarding CCNP

interface Loopback0
ip address 10.1.1.1 255.255.255.0

interface Loopback0
ip address 10.1.1.1 255.255.255.0
vrf forwarding CCNP

interface Loopback0
ip address 10.1.1.1 255.255.255.0
ip vrf forwarding CCNP

Q174. Refer to the exhibit.

TCP traffic should be reaching host 10.10.10.10/24 via R2. Which action resolves the issue?

TCP traffic will reach the destination via R2 without any changes

Add a permit 20 statement in the route map to allow TCP traffic

Allow TCP in the access list with no changes to the route map

Set IP next-hop to 10.10.12.2 under the route-map permit 10 to allow TCP traffic.

Q175.

Refer to the exhibit. An engineer configured two ASBRs, 10.4.17.6 and 10.4.15.5, in an OSPF network to redistribute identical routes from BGR However, only prefixes from 10.4.17.6 are installed into the routing table on R1. Which action must the engineer take to achieve load sharing for the BGP-originated prefixes?

The ASBRs are advertising the redistributed prefixes with the iBGP metric and must be modified to Type 1 on ASBR 10.4.17.6.

The ASBRs are advertising the redistributed prefixes with a different admin distance and must be changed to 110 on ASBR 10.4.15.5.

The admin distance of the prefixes must be adjusted to 20 on ASBR 10.4.15.5 to advertise prefixes to R1 identically from both ASBRs.

The ASBRs are advertising the redistributed prefixes as Type 1 and must be modified to Type 2

Q176. Refer to the exhibit.

R1 is connected with R2 via GigabitEthernet0/0, and R2 cannot ping R1. What action will fix the issue?

Fix route dampening configured on the router.

Replace the SFP module because it is not supported.

Fix IP Event Dampening configured on the interface.

Correct the IP SLA probe that failed.

Q177. Refer to the exhibit.

Which action resolves the failed authentication attempt to the router?

Configure aaa authorization login command on line vty 0 4

Configure aaa authorization login command on line console 0

Configure aaa authorization console global command

Configure aaa authorization console command on line vty 0 4

Q178. Refer to the exhibit.

The server for the finance department is not reachable consistently on the 200.30.40.0/24 network and after every second month it gets a new IP address. Which two actions must be taken to resolve this Issue? (Choose two.)