Aug 22, 2025 PASS Fortinet NSE7_SDW-7.2 EXAM WITH UPDATED DUMPS [Q33-Q48]

QUESTION 33
What are two reasons why FortiGate would be unable to complete the zero-touch provisioning process?
(Choose two.)

The FortiGate cloud key has not been added to the FortiGate cloud portal.

FortiDeploy has connected with FortiGate and provided the initial configuration to contact FortiManager

The zero-touch provisioning process has completed internally, behind FortiGate.

FortiGate has obtained a configuration from the platform template in FortiGate cloud.

A factory reset performed on FortiGate.

QUESTION 34
Refer to the exhibit.

Based on the exhibit, which two statements are correct about the health of the selected members? (Choose two.)

After FortiGate switches to active mode, FortiGate never fails back to passive monitoring.

During passive monitoring, FortiGate can’t detect dead members.

FortiGate can offload the traffic that is subject to passive monitoring to hardware.

FortiGate passively monitors the member if TCP traffic is passing through the member.

QUESTION 35
Refer to the exhibit.

Based on the output shown in the exhibit, which two criteria on the SD-WAN member configuration can be used to select an outgoing interface in an SD-WAN rule? (Choose two.)

Set priority 10.

Set cost 15.

Set load-balance-mode source-ip-ip-based.

Set source 100.64.1.1.

QUESTION 36
Refer to the exhibits.

Exhibit A shows the packet duplication rule configuration, the SD-WAN zone status output, and the sniffer output on FortiGate acting as the sender. Exhibit B shows the sniffer output on a FortiGate acting as the receiver.
The administrator configured packet duplication on both FortiGate devices. The sniffer output on the sender FortiGate shows that FortiGate forwards an ICMP echo request packet over three overlays, but it only receives one reply packet through T_INET_1_0.
Based on the output shown in the exhibits, which two reasons can cause the observed behavior? (Choose two.)

On the receiver FortiGate, packet-de-duplication is enabled.

The ICMP echo request packets sent over T_INET_0_0 and T_MPLS_0 were dropped along the way.

The ICMP echo request packets received over T_INET_0_0 and T_MPLS_0 were offloaded to NPU.

On the sender FortiGate, duplication-max-num is set to 3.

QUESTION 37
Which two statements about the SD-WAN zone configuration are true? (Choose two.)

Theservice-sla-tie-breaksetting enables you to configure preferred member selection based on the best
route to the destination.

You can delete the default zones.

The default zones are virtual-wan-link and SASE.

An SD-WAN member can belong to two or more zones.

QUESTION 38
What are two advantages of using an IPsec recommended template to configure an IPsec tunnel in an hub-and-spoke topology? (Choose two.)

It ensures consistent settings between phase1 and phase2.

It guides the administrator to use Fortinet recommended settings.

It automatically install IPsec tunnels to every spoke when they are added to the FortiManager ADOM.

The VPN monitor tool provides additional statistics for tunnels defined with an IPsec recommended template.

QUESTION 39
Which statement about SD-WAN zones is true?

An SD-WAN zone can contain only one type of interface.

An SD-WAN zone can contain between 0 and 512 members.

You cannot use an SD-WAN zone in static route definitions.

You can configure up to 32 SD-WAN zones per VDOM.

QUESTION 40
Refer to the exhibits.

Exhibit A shows two IPsec templates to define Branch_IPsec_1 and Branch_IPsec_2. Each template defines a VPN tunnel.
Exhibit B shows the error message that FortiManager displayed when the administrator tried to assign the second template to the FortiGate device.
Which statement best explain the cause for this issue?

You can assign only one template with a tunnel of fype static to each FortiGate device

You can define only one IPsec tunnel from branch devices to HUB1.

You can assign only one IPsec template to each FortiGate device.

You should review the branch1_fgt configuration for the already configured tunnel with the name HUB1-VPN2.

QUESTION 41
Refer to the exhibit.

Based on the exhibit, which two actions does FortiGate perform on traffic passing through port2? (Choose two.)

FortiGate does not change the routing information on existing sessions that use a valid gateway, after a route change.

FortiGate performs routing lookups for new sessions only, after a route change.

FortiGate always blocks all traffic, after a route change.

FortiGate flushes all routing information from the session table, after a route change.

QUESTION 42
The SD-WAN overlay template helps to prepare SD-WAN deployments. To complete the tasks performed by
the SD-WAN overlay template, the administrator must perform some post-run tasks. What are three
mandatory post-run tasks that must be performed? (Choose three.)

Create policy packages for branch devices.

Assign an sdwan_id metadata variable to each device (branch and hub}.

Configure routing through overlay tunnels created by the SD-WAN overlay template.

Assign a branch_id metadata variable to each branch device.

Configure SD-WAN rules.

QUESTION 43
In the default SD-WAN minimum configuration, which two statements are correct when traffic matches the
default implicit SD-WAN rule? (Choose two )

Traffic has matched none of the FortiGate policy routes.

Matched traffic failed RPF and was caught by the rule.

The FIB lookup resolved interface was the SD-WAN interface.

An absolute SD-WAN rule was defined and matched traffic.

QUESTION 44
Refer to the exhibits.

Exhibit A shows a policy package definition Exhibit B shows the install log that the administrator received when he tried to install the policy package on FortiGate devices.
Based on the output shown in the exhibits, what can the administrator do to solve the Issue?

Create dynamic mapping for the LAN interface for all devices in the installation target list.

Use a metadata variable instead of a dynamic interface to define the firewall policy.

Dynamic mapping should be done automatically. Review the LAN interface configuration for branch2_fgt.

Policies can refer to only one LAN source interface. Keep only the D-LAN, which is the dynamic LAN interface.

QUESTION 45
Refer to the exhibit.

Which conclusion about the packet debug flow output is correct?

The original traffic exceeded the maximum packets per second of the outgoing interface, and the packet was dropped.

The reply traffic exceeded the maximum bandwidth configured in the traffic shaper, and the packet was dropped.

The original traffic exceeded the maximum bandwidth of the outgoing interface, and the packet was dropped.

The original traffic exceeded the maximum bandwidth configured in the traffic shaper, and the packet was dropped.

QUESTION 46
Refer to the exhibits.
Exhibit A –

Exhibit B –

Exhibit A shows the SD-WAN performance SLA and exhibit B shows the SD-WAN member status, the routing table, and the performance SLA status.
If port2 is detected dead by FortiGate, what is the expected behavior?

Port2 becomes alive after three successful probes are detected.

FortiGate removes all static routes for port2.

The administrator manually restores the static routes for port2, if port2 becomes alive.

Host 8.8.8.8 is reachable through port1 and port2.

QUESTION 47
Refer to the exhibits.
Exhibit A

Exhibit B

Exhibit A shows an SD-WAN event log and exhibit B shows the member status and the SD-WAN rule configuration.
Based on the exhibits, which two statements are correct? (Choose two.)

FortiGate updated the outgoing interface list on the rule so it prefers port2.

Port2 has the highest member priority.

Port2 has a lower latency than port1.

SD-WAN rule ID 1 is set to lowest cost (SLA) mode.

QUESTION 48

Exhibit B –

Exhibit A shows the system interface with the static routes and exhibit B shows the firewall policies on the
managed FortiGate.
Based on the FortiGate configuration shown in the exhibits, what issue might you encounter when creating an
SD-WAN zone for port1 and port2?